Bio-Dur 560

Reinforced with Kevlar fibers. Highly tolerant of damp surfaces and can be applied underwater. An anticorrosive coating that is used to protect structures above or below the water and especially in the splash zone. Some versions are approved for Service Level 1 nuclear service.
REINFORCED EPOXY COATING FOR APPLICATION ABOVE OR BELOW WATER

BIO-DUR® 560 is based on a unique blend of liquid epoxy polymer and aliphatic polyamine curing agents, which is able to displace water from wet surfaces in order to make a permanent bond. The formulation is solvent-free to ensure safety and maximum technical performance. Kevlar®* microfibers are incorporated for reinforcement and viscosity management to achieve high application rates-even underwater! BIO-DUR 560 has successfully passed DBA test requirements for above or below water applied nuclear, Service Level 1 use.

BIO-DUR® 560 provides permanent protection under the most adverse conditions. The formula is uniquely field-friendly and uses advanced low toxicity ingredients in a high build brushable/rollable product. The sister product BIO-DUR® 561 is available if a higher viscosity, “light paste” consistency is required. All colors including White are available and can be shipped “Non-Regulated” by USDOT, IATA and IMO.

ANTICORROSIVE COATING:
Splash zone, abrasion resistance above or below water.

REPAIR COMPOUND:
Patching, leak sealing etc. above and below water.

FAIRING COMPOUND:
Smoothing rough steel and concrete.

ENCAPSULATING COATING:
Smooth, dense, easily decontaminated coating for steel and concrete.

WASTEWATER:
Reinforces, smooths and protects concrete exposed to chemical or municipal waste.

VEHICLE TYPE : Epoxy/Aliphatic amines

PIGMENTATION : Color/Inert/fibrous reinforcement

COLORS : Standard White, Black, Gray – other available

FINISH : Slight texture

THINNER : Not normally required

CLEANER : MEK or lacquer thinner

MIXING RATIO : 1.0/1.0 v/v

INDUCTION TIME : Not required

POT LIFE : Approx. 40° / 77°F

FLASH POINT :  Over 200°F

SOLIDS BY VOLUME : 100%

SPREADING RATE/GAL : 1604 mil/sq.ft./gal, 53.5 sq.ft./gal @ 30 mils

DRY TIME, (Dust free) : 4 hours at 77°F

DRY TIME, (Service) : 14 hrs. light, 72 hrs. heavy

APPLICATION METHOD : Brush, roller, heated plural airless spray

STORAGE CONDITIONS : Normal, Freezing OK

VOC : Essentially zero

SURFACE PREPARATION:

BELOW WATER: Remove marine biological settlement and corrosion by high pressure water jetting with or without abrasive. Conventional air/abrasive blasting works well at shallow depths however efficiency falls off sharply below, say, 10′. Hand held power tools such as needle guns or grinders can give good results if applied conscientiously in small areas but will be inadequate in large areas. Plan to apply the BIO-DUR®560 within 45 minutes maximum after surface preparation to minimize rerusting or initial settlement of fouling slime, which interferes with initial adhesion.

ABOVE WATER: Application above water requires similar high pressure water blasting or dry abrasive blasting to yield a firm, granular surface free of loose contamination. Since there is no problem from resettlement of marine fouling when working above water it is possible to delay application of the BIO-DUR 560 indefinitely provided fresh contamination of the cleaned surface does not occur.

MIXING PROCEDURE:

BIO-DUR® 560 is supplied either in 2 gallon or 4 gallon kits of 2xl, 2×2 or 2×5 gallon containers respectively each of epoxy base and curing agent. These components are formulated in contrasting colors to facilitate complete mixing. “Black” BIO-DUR® 560 for example is supplied with a jet black epoxy base and an off-white curing agent which mix together to yield a black mixture, visible streaks of either black or white seen during the course of mixing indicate “hotspots” unmixed components. It is imperative to properly mix the components since unmixed “hotspots” of either base or curing agent will never cure.

Remove equal quantities of base and curing agent from their cans and place them in a clean plastic or steel container. Mixing is easily accomplished by stirring with a “Jiffy” type mixer in a geared down, (high torque), 1/2″ electric drill. Once mixing begins there will be about 40 minutes of working time available at 80°F. This time may be extended by keeping the components and mixture cool, rather than leaving it in a hot area.

APPLICATION:

1) Using a stiff brush or roller apply from a tray of mixed material aiming for a coverage rate of about 50 sq.ft./ gallon.

2) Application by heated plural spray is easy using the following equipment setup:

Graco “King” or similar with heated hoses.
Mix ratio: 1/1 by volume
Fluid pressure: 2,500 psi
Fluid temp: 140°F
Filters:  Remove all filters
Tip size: .031″ -.039″ orifice

Note: For productivity estimate an application rate of one gallon per minute through a 0.035″ tip at 2,500 psi.

CURING BEFORE SERVICE:

BIO-DUR® 560 may be immersed in fresh or salt water immediately after application. It will cure to a hard film within about 14 hours and is suitable for traffic after this time. Allow at least three (3) days at 77°F before subjecting to aggressive chemical service from industrial solvents and similar materials.

TYPICAL PHYSICAL PROPERTIES OF THE CURED FILM:     

Compressive strength: 7,380 psi (50.9 N/mm2)
Tensile Strength: 6,000 psi (est.)
Flexural Strength: 4,550 psi (31.4 M/mm2)
Abrasion Resistance: 34.0 mg/1,000 cycles (CS17 wheels with 1,000 gram weights)


WE URGE YOU TO READ THE MATERIAL SAFETY DATA SHEET (MSDS) BEFORE USING AND TO CALL THIN FILM TECHNOLOGY, INC., AS NECESSARY FOR ADVICE OR INFORMATION BEFORE ANY ACTUAL OR CONTEMPLATED APPLICATION.

SAFETY: This is a hazardous material if misused. Read and understand the Material Safety Data Sheet (MSDS) before use.

WARRANTY DISCLAIMER: The technical data given herein has been compiled for your help and guidance and is based upon our experience and knowledge. However, as we have no control over the use to which this information is put, no warranty, express or implied, is intended or given. We assume no responsibility whatsoever for coverage, performance or damages, including injuries resulting from use of this information or of products recommended herein.

CH-031 CASE HISTORY EPOXY COATING APPLIED BY HEATED, PLURAL COMPONENT AIRLESS SPRAY TO GAS PIPELINE
CH-032 CASE HISTORY REPAIRS “BATHTUB RING” AT HANFORD
CH-036 CASE HISTORY PROTECTS AND SMOOTHS RIVERBOAT CASINO HULL
CH-040 CASE HISTORY SEALS UNDERWATER CONCRETE IN ORLANDO THEME PARK
CH-051 CASE HISTORY SEALS UNDERWATER SURFACES IN CONCRETE SPENT NUCLEAR STORAGE POOL
CH-054 CASE HISTORY LINER INSTALLATION IN SEA LION ENCLOSURE
CH-060 CASE HISTORY BLUE RELINES AND PROTECTS NUCLEAR TORUS
DOWNLOAD BIO-DUR® 560 PRODUCT DATA SHEET