Bio-Gard 254

Safety striping for use on busy commercial floors. 2/1 mixing ratio, quick-curing and odor-free for ease of use with no annoyance to adjacent trades.
LEAD-FREE CHROME-FREE SAFETY STRIPING

BIO-GARD™ 254 is a solvent-free, highly adhesive floor striping system designed for application over surfaces such as existing vinyl tiles and concrete. Thickness is typically 12 -20 mils which provides excellent wearability in a variety of colors.

BIO-GARD™ 254 is based on the same tough resin system as BIO- FLOR™ 182 and has given excellent results in the busiest materials handling facilities over several years per application. There is no perceptible odor during application and the film is cured for heavy service after 12 hours at 75°F with “dust-free” drying after about 4 hours.

BIO-GARD™ 254 has given excellent results on busy loading docks and has proved particularly effective when used with the BIO- FLOR™ 182 system for encapsulating old vinyl asbestos tile floors with a tougher seamless surface. Retro-reflective glass beads made be broadcast on its surface for increased visibility in low light.

LOADING DOCKS:
“Heavy Duty” striping for heavy wear areas. May be made slip resistant by mixing in an abrasive such as aluminum oxide or quartz.

VINYL ASBESTOS TILE:
Compatible with the BIO-FLOR™ 182 encapsulation system.

FOOD HANDLING FACILITIES:
Meets USDA PSIS Directive 11,000.4 ” Approval Of Paints and Coatings Used in Official Establishments” dated 8/12/94 for floors.

VEHICLE TYPE : Epoxy/Aliphatic amines

PIGMENTATION : Lead and Chromium free color/inert

COLORS : All colors including white

FINISH : High gloss

THINNER : Not normally required

CLEANER : MEK or lacquer thinner

MIXING RATIO : varies with color – approximately 2/1 by volume

INDUCTION TIME : Not required

POT LIFE : Approx. 15’/77°F

FLASH POINT : Over 200°F

SOLIDS BY VOLUME : 100%

SPREADING RATE/GAL : Normally 300 linear feet of 4” stripe per gallon

DRY TIME, (LIGHT TRAFFIC) : 12 hours at 77°F

APPLICATION METHOD : Squeegee/roller, roller

VOC : Essentially zero

SURFACE PREPARATION:

This may be accomplished in several ways:

New Concrete: leave to cure properly for a minimum of 20 days before coating. Weak surface laitance must be removed by either acid etching or abrasive blasting. (Note: acid etching can be difficult and unreliable unless performed with particular attention to proper acid application, scrubbing, rinsing and drying.) Abrasive blasting, (recommended), may be effected by conventional open blasting or with “Blastrac”® type centrifugal equipment. The concrete surface after preparation should have the granular appearance of medium sandpaper.

Aged Concrete: best prepared by abrasive blasting. If contaminated contact Thin Film Technology for advice.

Coated Concrete: if existing coatings are unsound they must be removed by abrasive blasting before BIO-GARD™ 254 application. Worn but sound coatings may be prepared by vigorous scrubbing with detergent/stripper using an aggressive janitorial scrubber. The surface should be absolutely clean and matt before coating.

Vinyl Asbestos/Vinyl Composition Tile: Prepare for coating by scrubbing with wax stripper using a janitorial scrubber. (Note: when stripping vinyl asbestos tile, (VAT), use no more aggressive pad than a green pad in accordance with OSHA directives – under no circumstances abrade the tile surface). Check the pH of the surface after stripping using pH test paper -rinse until pH is in the range 6- 8.5. Vacuum, squeegee or blow-dry the surface before coating application.

MIXING PROCEDURE:

Use a “Jiffy” type mixer on a high torque, (geared down), ½” electric drill to first stir the part filled epoxy base unit then add the curing agent and mix thoroughly for at least one minute. Note: Unmixed components will never cure. Apply the mixed material to the masked stripe area immediately -sweat-in or induction time is not required. Plan to use the entire mixed kit within 10- 15 minutes by using two or more painters if necessary.

APPLICATION:

Mark the layout of the striping using chalk strings or similar tools then mask on either side of the line using strong masking tape or duct tape. Apply the BIO-GARD™ 254 using either a brush or roller applying a full coat for best results

Note: BIO-GARD™ 254 is 100% solvent-free -application of excess material is not harmful; noffi1al curing will take place in any thickness.

Remove masking tape before the BIO-GARD™ 254 has set hard. Early removal allows a soft and attractive edge to the stripe.

CURING BEFORE SERVICE:

Allow 12hrs curing at 77°F before initial service, which includes rolling, but not spinning, wheeled traffic. Unlimited service is possible after about 24 hrs. at 77°F with “full cure” occurring about 3 days after the last coating application.


WE URGE YOU TO READ THE MATERIAL SAFETY DATA SHEET (MSDS) BEFORE USING AND TO CALL THIN FILM TECHNOLOGY, INC., AS NECESSARY FOR ADVICE OR INFORMATION BEFORE ANY ACTUAL OR CONTEMPLATED APPLICATION.

SAFETY: This is a hazardous material if misused. Read and understand the Material Safety Data Sheet (MSDS) before use.

WARRANTY DISCLAIMER: The technical data given herein has been compiled for your help and guidance and is based upon our experience and knowledge. However, as we have no control over the use to which this information is put, no warranty, express or implied, is intended or given. We assume no responsibility whatsoever for coverage, performance or damages, including injuries resulting from use of this information or of products recommended herein.

DOWNLOAD BIO-GARD™ 254 PRODUCT DATA SHEET